PIV Analysis of Inner Flow Field in 90° Bending Duct of Circular-Section with Fore-End Valve

Abstract

Abstract:Through the established recirculation water channel, the inner flow field in 90° bending duct of circular-section with a fore-end valve was measured by particle image velocimetry (PIV). Characteristics of the flow were obtained through correlation analysis of the massive consecutive high-resolution transient velocity maps, including time-averaged velocity field, streamline pattern and vorticity distributions. Through comparative analysis of the time-averaged velocity field: it is concluded that there exist apparent high-speed and lowspeed regions in the bend part; a vortex emerges on specific conditions; the features of the flow field vary considerably along with the diversity of valve opening magnitude, flow rate and section location.

Key words:valve,bend,flow field,particle image velocimetry (PIV),correlation analysis

CLC Number:

TV131

XIE Long-1, JIN Si-Yu-1, 2 , YU Jian-Guo-1, WANG Yu-Zhang-1. PIV Analysis of Inner Flow Field in 90° Bending Duct of Circular-Section with Fore-End Valve[J]. Journal of Shanghai Jiaotong University, 2011, 45(09): 1395-1399.

References

［1］江山，张京伟，吴崇健，等. 基于FLUENT的90°圆形弯管内部流场分析［J］. 中国舰船研究，2008，3(1)： 3741.

JIANG Shan, ZHANG Jingwei, WU Chongjian, et al. Numerical simulation of inner flow in 90° bending duct of crcularsection based on FLUENT［J］. Chinese Journal of Ship Research, 2008, 3(1): 3741.

［2］丁珏，翁培奋. 90°弯管内流动的理论模型及流动特性的数值研究［J］. 计算力学学报，2004，21(3)：314321.

DING Jue, WENG Peifen. Numerical simulation of theoretical models and flow characteristics in 90° bending duct［J］. Chinese Journal of Computational Mechanics, 2004, 21(3): 314321.

［3］樊洪明，何钟怡，王小华. 弯曲管段内流动的大涡模拟［J］.水动力学研究与进展，2001，16(1)：7883.

FAN Hongming, HE Zhongyi, WANG Xiaohua. Large eddy simulation of a curved duct flow［J］. Journal of Hydrodynamics, 2001, 16(1): 7883.

［4］Sudo K, Sumida M, Hibara H. Experimental investigation on turbulent flow in a circularsectioned 90degree bend［J］. Experiments in Fluids, 1998, 25(1): 4249.

［5］Taylor A M K P, Whitelaw J H, Yianneskis M. Curved ducts with strong secondary motion: Velocity measurements of developing laminar and turbulent flow［J］. Journal of Fluids Engineering, 1982, 104(3): 350360.

［6］尚虹，王尚锦，席光，等. 90°圆截面弯管内三维紊流场试验研究［J］. 航空动力学报，1994，9(3)：263266.

SHANG Hong, WANG Shangjin, XI Guang, et al. Experimental study of 3D turbulent flow field in a 90° bend pipe［J］. Journal of Aerospace Power, 1994, 9(3): 263266.

［7］万津津，施鎏鎏，刘应征，等. 贴壁方柱湍流场高分辨率PIV试验研究［J］. 开云网页登录学报，2009，43(2)：322324.

WAN Jinjin, SHI Liuliu, LIU Yingzheng, et al. Highresolution PIV measurement of the wake behind a square cylinder flushmounted on the wall［J］. Journal of Shanghai Jiaotong University, 2009, 43(2): 322324.

[1]	WANG Zhiwei, HE Yanping, LI Mingzhi, QIU Ming, HUANG Chao, LIU Yadong.Numerical Simulation and Flow Pattern Evolution of Gas-Liquid Two-Phase Flow Passing Through a 90° Pipe Bend Based on CFD[J]. Journal of Shanghai Jiao Tong University, 2022, 56(9): 1159-1167.
[2]	LIU Qingsheng, XUE Hongxiang, YUAN Yuchao, TANG Wenyong.Bending Properties of Unbonded Flexible Risers with Composite Materials[J]. Journal of Shanghai Jiao Tong University, 2022, 56(9): 1247-1255.
[3]	LI Peng, WANG Chao, SUN Huawei, GUO Chunyu.Numerical Simulation Strategy Optimization Analysis of Submarine Resistance and Flow Field[J]. Journal of Shanghai Jiao Tong University, 2022, 56(4): 506-515.
[4]	HU Jinshuo, HUANG Jianzhe.Dynamics Modeling and Validation of Coaxial Lifting Rotors[J]. Journal of Shanghai Jiao Tong University, 2022, 56(3): 395-402.
[5]	RONG Zhen, HU Wenjie, QIU Yunlong, ZHANG Yujian, WANG Yizhuang, JIANG Zhongzheng, CHEN Weifang.Φ120 Hypersonic Wind Tunnel Flow Field Calibration[J]. Air & Space Defense, 2022, 5(3): 58-64.
[6]	HUANG Jiayang (黄嘉阳), YANG Pengfei* (杨鹏飞), WAN Bo (万波), ZHANG Zhiqiang (张志强).KDLPCCA-Based Projection for Feature Extraction in SSVEP-Based Brain-Computer Interfaces[J]. J Shanghai Jiaotong Univ Sci, 2022, 27(2): 168-175.
[7]	WU Tao, MO Shixu, XIANG Yongbin, ZOU Zequn, ZHENG Yan.Explicit Buckling Analysis of Rotationally Restrained Plates on Rigid Base Under Various Loading Conditions[J]. Journal of Shanghai Jiao Tong University, 2022, 56(1): 114-126.
[8]	ZHENG Gaoyuan, ZHAO Yixi, CUI Junhui.Formation Law of Surface Defects in Stretch-Bending Formamtion of Aluminum Trim Strip for Automobile Body[J]. Journal of Shanghai Jiao Tong University, 2022, 56(1): 53-61.
[9]	LIU Hao , ZHANGNing , WANG Huoping , ZHU Liyun , ZHANG Yu .A Method for Improving the Motion Performance of Steel Catenary Riser by Adding Inertia Bodies to the Sagbend Section #br#[J]. Ocean Engineering Equipment and Technology, 2022, 9(1): 37-45.
[10]	XU Dehui, GU Hanyang, LIU Li, HUANG Chao.Thermal Experimental and Numerical Study on Performance of a Novel Conical Swirl-Vane Steam Separator[J]. Journal of Shanghai Jiao Tong University, 2021, 55(9): 1087-1094.
[11]	JIANG Chenqi (江晨琦), GONG Zhaoxin (宫兆新) .Effect of Deflectors on the Flow Characteristics of a Square Pipe with a 90° Bend[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(2): 163-169.
[12]	WANG Yufeng,WANG Dandong,HU Jichao,CHEN Liang,CHEN Jiangping.A Numerical Model of the Two-Phase CO2 Ejectors[J]. Journal of Shanghai Jiaotong University, 2019, 53(7): 860-865.
[13]	ZHANG Xiaohui (张晓慧), GU Xiechong (顾解忡), MA Ning (马宁), WANG Yifan (王一凡), WU Zeren (吴泽仁).Experimental Investigation into the Effect of Roll Amplitude on Roll Damping[J]. Journal of Shanghai Jiao Tong University (Science), 2019, 24(6): 732-738.
[14]	XU Hongchang (徐宏昌), LIU Shuangzhai (刘双寨), PAN Haoxing (潘浩星).Spray Characteristics with High-Speed Tomographic Particle Image Velocimetry Under Non-Flash and Flash Boiling Conditions[J]. Journal of Shanghai Jiao Tong University (Science), 2019, 24(5): 591-596.
[15]	HUANG Tao (皇涛), WANG Kun (王锟), ZHAN Mei (詹梅), GUO Junqing (郭俊卿), CHEN Xuewen (陈学文), CHEN Fuxiao (陈拂晓), SONG Kexing (宋克兴).Wall Thinning Characteristics of Ti-3Al-2.5V Tube in Numerical Control Bending Process[J]. Journal of Shanghai Jiao Tong University (Science), 2019, 24(5): 647-653.